New Original Phoenix Single-Phase Switching Power Supply - Quint4-PS/1AC/24DC/10/Co - 2904625

Article Number    2904625
Width    50 mm
Height    130 mm
Depth    125 mm
Width with alternative assembly    122 mm
Height with alternative assembly    130 mm
Depth with alternative assembly    53 mm
Installation distance right/left    5 mm / 5 mm
Installation distance top/bottom    50 mm / 50 mm
Degree of protection    IP20
Inflammability class in acc. with UL 94 (housing / terminal blocks)    V0
Ambient temperature (operation)    -25 °C … 70 °C (> 60 °C Derating: 2,5 %/K)
Ambient temperature (start-up type tested)    -40 °C
Ambient temperature (storage/transport)    -40 °C … 85 °C
Max. permissible relative humidity (operation)    ≤ 100 % (at 25 °C, non-condensing)
Climatic class    3K3 (in acc. with EN 60721)
Degree of pollution    2
Installation height    ≤ 5000 m (> 2000 m, observe derating)
Nominal input voltage range    100 V AC … 240 V AC
110 V DC … 250 V DC
Input voltage range    100 V AC … 240 V AC -15 % … +10 %
110 V DC … 250 V DC -18 % … +40 %
Dielectric strength maximum    300 V AC 60 s
AC frequency range    50 Hz … 60 Hz -10 % … +10 %
Frequency range (fN)    50 Hz … 60 Hz -10 % … +10 %
16.7 Hz (acc. to EN 50163)
Discharge current to PE    < 3.5 mA
Current consumption    3.4 A (100 V AC)
2.8 A (120 V AC)
1.5 A (230 V AC)
1.5 A (240 V AC)
Nominal power consumption    274 VA
Inrush current    typ. 12 A (at 25 °C)
Mains buffering time    typ. 42 ms (120 V AC)
typ. 44 ms (230 V AC)
Input fuse    8 A (slow-blow, internal)
Recommended breaker for input protection    10 A … 16 A (Characteristic B, C, D, K or comparable)
Power factor (cos phi)    0.94
Type of protection    Transient surge protection
Protective circuit/component    Varistor, gas-filled surge arrester
Nominal output voltage    24 V DC
Setting range of the output voltage (USet)    24 V DC … 29.5 V DC (constant capacity)
Nominal output current (IN)    10 A
Static Boost (IStat.Boost)    12.5 A
Dynamic Boost (IDyn.Boost)    20 A (5 s)
Selective Fuse Breaking (ISFB)    60 A (15 ms)
Derating    > 60 °C (2.5%/K)
Connection in parallel    yes, for redundancy and increased capacity
Connection in series    yes
Feedback voltage resistance    ≤ 35 V DC
Protection against overvoltage at the output (OVP)    ≤ 32 V DC
Control deviation    < 0.5 % (Static load change 10 % … 90 %)
< 4 % (Dynamic load change 10 % … 90 %, (10 Hz))
< 0.25 % (change in input voltage ±10 %)
Residual ripple    < 80 mVPP (with nominal values)
Output power    240 W
Typical response time    300 ms (from SLEEP MODE)
Maximum power dissipation in no-load condition    < 3 W (120 V AC)
< 3 W (230 V AC)
Power loss nominal load max.    < 20 W (120 V AC)
< 17 W (230 V AC)
Net weight    0.9 kg
Environmental protection directive    RoHS Directive 2011/65/EU
WEEE
Reach
Efficiency    typ. 92.5 % (120 V AC)
typ. 93.4 % (230 V AC)
MTBF (IEC 61709, SN 29500)    > 1251000 h (25 °C)
> 783000 h (40 °C)
> 377000 h (60 °C)
Insulation voltage input/output    4 kV AC (type test)
2 kV AC (routine test)
Insulation voltage input / PE    3.5 kV AC (type test)
2.4 kV AC (routine test)
Insulation voltage output / PE    0.5 kV DC (type test)
0.5 kV DC (routine test)
Degree of protection    IP20
Protection class    I
Inflammability class in acc. with UL 94 (housing / terminal blocks)    V0
Mounting position    horizontal DIN rail NS 35, EN 60715
Assembly instructions    alignable: PN ≥50%, 5 mm horizontally, 15 mm next to active components, 50 mm vertically
alignable: PN <50%, 0 mm horizontally, 40 mm vertically top, 20 mm vertically bottom
Connection method    Screw connection
Conductor cross section solid min.    0.2 mm²
Conductor cross section solid max.    2.5 mm²
Conductor cross section flexible min.    0.2 mm²
Conductor cross section flexible max.    2.5 mm²
Conductor cross section AWG min.    24
Conductor cross section AWG max.    14
Stripping length    6.5 mm